• 

  Nov. 21, 2011 10:33 p.m. carguy123 SuperDork

  I need to recover the top of a bench prior to Thanksgiving and the arrival of all the company.

  I have a vinyl cover I need to remove and replace with fabric. Fabric breathes and vinyl doesn't hence it would blow up like a balloon when you sat on it and it eventually broke thru in some weak places, but that's not what this is all about.

  I have umpteen gillion staples around the edges I need to remove before I can recover it. The underlying base is made of particle board. Is there a quicker and easier way to remove all those staples than with a screwdriver?

• 

  Nov. 21, 2011 10:59 p.m. motomoron HalfDork

  I had to take a bunch out of the back of a folding futon-sofa thing. After the screwdriver method on the first 5 of 100, I grabbed an old "Painter's 5-in-1" tool and ground a thin chisel that was just a hair narrower than the inside dimension of a staple. Push and wiggle it under then lift to pop the staple out. Took about 4 seconds a staple + 10 minutes to make the tool.

  "All my tools are hammers except screwdrivers which are chisels and punches"

• 

  Nov. 21, 2011 11:07 p.m. fasted58 SuperDork

  an awl or that sharpened painter tool to dig n loosen if they're tight, nippers to finish

• 

  Nov. 21, 2011 11:09 p.m. oldtin Dork

  I have a carpet guy's staple remover - curved handle with a flat front and a little blade to dig under the staples. Works like a charm - like a second or two a staple. Like this only about 30 years older.

  
• 

  Nov. 22, 2011 6:30 a.m. Ian F SuperDork

  In reply to oldtin:

  Yep. One of these will save much frustration... if it only pulls up one side, grab the staple with a pair of channel-locks, then lever/roll it out.
  

  When we demo'd the g/f's kitchen floor, the linoleum had been glued down over 1/4" plywood that had been stapled down with 1" long, 1/4" staples. Most of the time, the staples would pull through the ply and remain in the sub-floor. We were cursing the inventor of the pnuematic staple gun and I got very good at pulling them out with channel-locks...

• 

  Nov. 22, 2011 7:38 a.m. oldsaw SuperDork

  I used a set of wire-cutting pliers similar to these after pulling carpet on the stairs:

  

  Wedge one side into the loop and use leverage to get the staple out. When a staple broke, a pair of regular pliers was used to pull-out the ends.

• 

  Nov. 22, 2011 7:49 a.m. Giant Purple Snorklewacker SuperDork

  oldsaw wrote: I used a set of wire-cutting pliers similar to these after pulling carpet on the stairs: Wedge one side into the loop and use leverage to get the staple out. When a staple broke, a pair of regular pliers was used to pull-out the ends.

  +1, except I use Channellock end cutter pliers:

  Lord of drivel and harbinger of Floundering

• 

  Nov. 22, 2011 8:01 a.m. iceracer SuperDork

  My staple gun came with a staple remover. Just a little tapered pry bar.

• 

  Nov. 22, 2011 8:05 a.m. pinchvalve SuperDork

  When removing carpet padding, I used a flat screwdriver and a spring-loaded pair of pliers. The screwdriver popped out one side, then I grabbed it and pulled it out with the pliers. The spring makes it a one-handed tool. I could do 2-3 per second.

  "Don't Sweat the Petty Things." Yes, and Don't Pet the Sweaty Things.

• 

  Nov. 22, 2011 8:17 a.m. akamcfly Reader

  

  Someone had to...

• 

  Nov. 22, 2011 9:42 a.m. Ian F SuperDork

  The above tools will work fine for a handful of staples, but it you have a lot to remove, grab one of these:

  

  Grab the staple and roll it out. After the 50th staple, you'll appreciate the less effort required due to the long handles. After the 500th staple, you're looking for every possible way to reduce effort and make the task faster.

  We really wanted to kill the guy who installed the underlayment... "I got this new toy and 6000 staples to burn through..."

• 

  Nov. 22, 2011 10:48 a.m. carguy123 SuperDork

  Thanx. I'll head down to Lowes to see if they have one of these at lunch.

  oldtin wrote: I have a carpet guy's staple remover - curved handle with a flat front and a little blade to dig under the staples. Works like a charm - like a second or two a staple. Like this only about 30 years older.

  "mobilito ergo sum" I drive therefore I am!

• 

  Nov. 22, 2011 10:55 a.m. Grtechguy SuperDork

  Another vote for the channel locks. that thing ^^^ assumes the staple isn't flush to the floor

  bouncing around the screen like a chihuahua on a meth binge.

• 

  Nov. 22, 2011 11:28 a.m. carguy123 SuperDork

  They are flush to the floor which means I have to pry and then grab with some sort of pliers, that's why I like the idea of the staple puller thingy. Now if I can only find one.

  "mobilito ergo sum" I drive therefore I am!

• 

  Nov. 22, 2011 12:54 p.m. Ian F SuperDork

  For the flush ones, I used a flat screw driver to pry them up enough for the channel locks to grip them. The problem with the puller tool (we have one at work) is it will often only pull up one of the tangs, so you still have to plier it out.

• 

  Nov. 22, 2011 2:16 p.m. carguy123 SuperDork

  NOBODY has such a beast. I even tried the fabric/upholstery stores.

  I guess I'm prying and pulling.

  "mobilito ergo sum" I drive therefore I am!

• 

  Nov. 22, 2011 2:33 p.m. Ian F SuperDork

  Office supply store?

  The tool pictured above was hotlinked from http://westerntradesupply.com that sells contractor flooring tools. It looks like you'll need to call to get a price.

• 

  Nov. 22, 2011 3:59 p.m. carguy123 SuperDork

  I can't wait. I have company coming Thursday so I have to be finished by then.

  My screwdriver type pry tool is working, it's just slow and more work than I'd have to do if I had an all in one tool

  "mobilito ergo sum" I drive therefore I am!

• 

  Nov. 22, 2011 4:06 p.m. oldtin Dork

  http://www.grainger.com/Grainger/Staple-Remover-4PMD6?Pid=searchgot a grainger near you?

• 

  Nov. 22, 2011 5:01 p.m. carguy123 SuperDork

  oldtin wrote: http://www.grainger.com/Grainger/Staple-Remover-4PMD6?Pid=searchgot a grainger near you?

  No

  "mobilito ergo sum" I drive therefore I am!

• 

  Nov. 22, 2011 5:02 p.m. RX Reven' HalfDork

  Oh man, I jumped into this thread expecting to see cool stuff like this:

  

  “There is no try…only succeed & succeed not”

• 

  Nov. 22, 2011 5:18 p.m. carguy123 SuperDork

  Yeah, I 've got one of those.

  I sat around one night watching TV & removing the staples from my groin area.

  "mobilito ergo sum" I drive therefore I am!

You'll need to log in to post.