• 

  Feb. 21, 2010 4:30 p.m. redzcstandardhatch Reader

  i really liked the 25 hours of thunderhill article.

  i took two poops while reading it.

  then i kept reading the challenge article. what a great time.
  

  oh, and the header for gutty was pulled out of the KING MOTORSPORTS dumpster, by splitime...not myself (as stated in the blurb) luke screwed thatup in his build thread/documentation.

  GREAT issue

• 

  Feb. 21, 2010 5:30 p.m. aussiesmg SuperDork

  I am going to have to do some dumpster diving I guess, I need headers

  Cornering is like bringing a woman to climax. Jackie Stewart

• 

  Feb. 21, 2010 5:31 p.m. redzcstandardhatch Reader

  it was so smashed it wasnt a header again until we chopped it into about 50 pieces. one tube was so kinked it almost wouldnt flow anything

• 

  Feb. 21, 2010 5:39 p.m. aussiesmg SuperDork

  It looks like I will have to build some, I can get small tubed ones easily but 1 3/4" are difficult to find cheap.

  Cornering is like bringing a woman to climax. Jackie Stewart

• 

  Feb. 21, 2010 5:43 p.m. eastpark New Reader

  redzcstandardhatch wrote: i really liked the 25 hours of thunderhill article. i took two poops while reading it. GREAT issue

  Interesting critique comment... Just imagine Gene Shalit using it for a movie review....

• 

  Feb. 21, 2010 6:04 p.m. unevolved Reader

  aussiesmg wrote: It looks like I will have to build some, I can get small tubed ones easily but 1 3/4" are difficult to find cheap.

  Here's a hint: sand bending. We're at the same place with our build.

  Texas A&M Racing

• 

  Feb. 21, 2010 6:39 p.m. Fair New Reader

  unevolved wrote:

  aussiesmg wrote: It looks like I will have to build some, I can get small tubed ones easily but 1 3/4" are difficult to find cheap.

  Here's a hint: sand bending. We're at the same place with our build.

  Same here. Cannot find headers that fit our goofy swap, so I'm looking for cheap bends to make custom headers. Its hard to find mandrel bent pieces cheap. :(

  Terry Fair @ Vorshlag Motorsports

• 

  Feb. 21, 2010 6:41 p.m. redzcstandardhatch Reader

  eastpark wrote:

  redzcstandardhatch wrote: i really liked the 25 hours of thunderhill article. i took two poops while reading it. GREAT issue

  Interesting critique comment... Just imagine Gene Shalit using it for a movie review....

  if he asks, tell him i give permission

• 

  Feb. 21, 2010 6:56 p.m. maroon92 SuperDork

  I have not read it yet, but I noticed that the 25 hours article was slightly longer than usual. Did JG finally finish one?

  "there is no horrible way to win, there is only winning" -Jean Pierre Sarti

• 

  Feb. 21, 2010 7:20 p.m. P71 SuperDork

  Fair wrote: Same here. Cannot find headers that fit our goofy swap, so I'm looking for cheap bends to make custom headers. Its hard to find mandrel bent pieces cheap. :(

  Summit Racing is your friend. Anyplace that sells roundy-round stuff is good also. Cheapo generic V8 headers are under $100 on Summit, hack them up and make a pair of good un's!

  Michael Pinto - 73 AMC Hornet / 93 Miata STS / 01 P71 Interceptor

You'll need to log in to post.